亀井です。
ただいま製品版のKondara2.0(Linux 2.4.4-18k)を使用しています。
はっきりとした理由は分からないのですが、起動に時間がかかるこ
とが最近結構な頻度であります。
boot時のメッセージを眺めていると、、、
「Turning on user and group quotas for local filesystem」
と
「Init: Entering runlevel 5」
の間です。最後にdmsgを付けます。
ちょっとHDDを疑ってreiserfsck --checkを試してみました。
明らかにエラーが出たパーティションがあったのでそこは
--fix-fixableをかけましたが、
どうしても
「Checking Semantic tree... /hoge/hoga/nyoro」
みたいなのは残ってしまいます。
これって、問題ないのでしょうか？
ちなみにKondaraのFAQに従ってlilo.confには
「append="acpi=no-idle acpi=off apm=on"」
をいれてあります。
まー、起動は遅くても立ち上がれば問題ないしHDDも大丈夫なよう
な気がするのですが、、、なんせノートなので結構起動停止を３年
繰り返していると不安は残ります。
他になにかチェックするところはあるでしょうか？
dmesgのlog
-------------------------------------------
Linux version 2.4.4-18k (dyky _at_ mukiri.kondara.org) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Tue Jun 5 06:50:09 PDT 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e5400 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
Scan SMP from c009f800 for 4096 bytes.
On node 0 totalpages: 32768
zone(0): 4096 pages.
zone(1): 28672 pages.
zone(2): 0 pages.
mapped APIC to ffffe000 (01223000)
Kernel command line: auto BOOT_IMAGE=linux ro root=307 acpi=off apm=on
Initializing CPU#0
Detected 332.171 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 661.91 BogoMIPS
Memory: 126392k/131072k available (1155k kernel code, 4292k reserved, 445k data, 224k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Celeron (Mendocino) stepping 0a
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch _at_ atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd9be, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
got res[10000000:10000fff] for resource 0 of Ricoh Co Ltd RL5c475
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
IA-32 Microcode Update Driver: v1.08 <tigran _at_ veritas.com>
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 83925kB/27975kB, 256 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcb0-0xfcb7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfcb8-0xfcbf, BIOS settings: hdc:pio, hdd:pio
hda: TOSHIBA MK8113MAT, ATA DISK drive
hdc: UJDA140, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 16006410 sectors (8195 MB), CHS=996/255/63, UDMA(33)
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
NET4: Frame Diverter 0.46
Real Time Clock Driver v1.10d
Non-volatile memory driver v1.1
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
ACPI: Disabled
IEEE 802.2 LLC for Linux 2.1 (c) 1996 Tim Alpaerts
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
IP-Config: No network devices available.
ip_tables: (c)2000 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
reiserfs: checking transaction log (device 03:07) ...
Using r5 hash to sort names
ReiserFS version 3.6.25(w/quota support)
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
Adding Swap: 136512k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.259 $ time 07:09:07 Jun 5 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0xfc20, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF c7afd520, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: fc20
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c7afd520
usb.c: kusbd: /sbin/hotplug add 1
hub.c: port 1 connection change
hub.c: port 1, portstatus 301, change 1, 1.5 Mb/s
hub.c: port 1, portstatus 303, change 0, 1.5 Mb/s
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: kmalloc IF c7afd6a0, numif 1
usb.c: skipped 1 class/vendor specific interface descriptors
usb.c: new device strings: Mfr=0, Product=1, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Product: USB Mouse
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0x5e3/0x1205) is not claimed by any active driver.
Length = 18
DescriptorType = 01
USB version = 1.00
Vendor:Product = 05e3:1205
MaxPacketSize0 = 8
NumConfigurations = 1
Device version = 2.30
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0022
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = a0
MaxPower = 48mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 01
bInterface Class:SubClass:Protocol = 03:01:02
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0004
bInterval = 0a
usb.c: kusbd: /sbin/hotplug add 2
usb.c: registered new driver usb_mouse
input0: USB Mouse on usb1:2.0
usb.c: usb_mouse driver claimed interface c7afd6a0
usb.c: registered new driver hid
mouse0: PS/2 mouse device for input0
mice: PS/2 mouse device common for all mice
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
reiserfs: checking transaction log (device 03:05) ...
Using rupasov hash to sort names
reiserfs: using 3.5.x disk format
ReiserFS version 3.6.25(w/quota support)
reiserfs: checking transaction log (device 03:08) ...
Using r5 hash to sort names
ReiserFS version 3.6.25(w/quota support)
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw _at_ saw.sw.com.sg> and others
PCI: Found IRQ 9 for device 00:0b.0
PCI: The same IRQ used for device 00:09.0
divert: allocating divert_blk for eth0
eth0: OEM i82557/i82558 10/100 Ethernet, 00:80:45:11:1E:77, I/O at 0xfc40, IRQ 9.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 4d3031-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Receiver lock-up workaround activated.
eth0: 0 multicast blocks dropped.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
Linux PCMCIA Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 10 for device 00:0a.0
PCI: The same IRQ used for device 01:00.1
Yenta IRQ list 08b8, PCI irq10
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x338-0x33f 0x378-0x37f 0x3f8-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
NeoMagic 256AV/256ZX audio driver, version 1.1
NM256: Forcing driver load as per user request.
NM256: Found card signature in video RAM: 0x27ec00
NM256: Mapping port 1 from 0x266c00 - 0x27ec00
Initialized NeoMagic 256AV audio in PCI native mode
Initialized AC97 mixer
Done installing NM256 audio driver.
---
亀井 孝幸
kamei _at_ attglobal.net
www.reallife.jp