[Subject Prev][Subject Next][Thread Prev][Thread Next][Subject Index][Thread Index]

[linux-users:00013] About XFree86

はじめまして、Linux初心者の新垣と申します。
Linuxをインストールして１週間ぐらいになるのですが、
XFree86の設定ではまっており、Linuxでいろいろやりたいことあるに
先に進めません。
そこで、諸先輩方々のお知恵を拝借したいと思っております。
以下に、パソコンの構成と、error log、XF86Configを添付します。

-------------------- cut errorlog ------------------------
XFree86 Version 3.2 / X Window System
(protocol Version 11, revision 0, vendor release 6100)
Release Date: Oct 26 1996
	If the server is older than 6-12 months, or if your card is newer
	than the above date, look for a newer version before reporting
	problems.  (see http://www.XFree86.Org/FAQ)
Operating System: Linux [ELF] 
Configured drivers:
  S3: accelerated server for S3 graphics adaptors (Patchlevel 0)
      s3_ViRGE
(using VT number 7)

XF86Config: /etc/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) Mouse: type: PS/2, device: /dev/mouse, baudrate: 1200,
       3 button emulation (timeout: 50ms)
(**) S3: Graphics device ID: "S3-ViRge"
(**) S3: Monitor ID: "SC-528MXLJ"
(--) S3: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/l

ib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/font

s/100dpi/"
(--) S3: PCI: ViRGE rev 6, Linear FB @ 0xe0000000
(**) S3: Unknown RAMDAC type "s3gendac"

 *** A configured device found, but display modes could not be resolved.***

-------------------- cut errorlog end ------------------------

----------------------- cut XF86Config -----------------------
# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of 
# this file.
# **********************************************************************

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# 
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
# 

    FontPath	"/usr/X11R6/lib/X11/fonts/misc/"
    FontPath	"/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath	"/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath	"/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath	"/usr/X11R6/lib/X11/fonts/100dpi/"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    NoTrapSignals

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    DontZap

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    DontZoom

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Keyboard section
# **********************************************************************

Section "Keyboard"

    Protocol	"Standard"

# when using XQUEUE, comment out the above line, and uncomment the
# following line

#    Protocol	"Xqueue"

    AutoRepeat	500 5
# Let the server do the NumLock processing.  This should only be required
# when using pre-R6 clients
#    ServerNumLock

# Specifiy which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Xleds      1 2 3

# To set the LeftAlt to Meta, RightAlt key to ModeShift, 
# RightCtl key to Compose, and ScrollLock key to ModeLock:

    LeftAlt     Meta
    RightAlt    ModeShift
#    RightCtl    Compose
#    ScrollLock  ModeLock

EndSection


# **********************************************************************
# Pointer section
# **********************************************************************

Section "Pointer"
    Protocol    "PS/2"
    Device      "/dev/mouse"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Protocol	"Xqueue"

# Baudrate and SampleRate are only for some Logitech mice

#    BaudRate	9600
#    SampleRate	150

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

    Emulate3Buttons
    Emulate3Timeout    50

# ChordMiddle is an option for some 3-button Logitech mice

#    ChordMiddle

EndSection


# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "SC-528MXLJ"
    VendorName  "SAMPTON"
    ModelName   "TFT"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   24-66

#    HorizSync	30-64         # multisync
#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-120

# Modes can be specified in two formats.  A compact one-line format, or
# a multi-line format.

# These two are equivalent

#    ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace

#    Mode "1024x768i"
#        DotClock	45
#        HTimings	1024 1048 1208 1264
#        VTimings	768 776 784 817
#        Flags		"Interlace"
#    EndMode

# This is a set of standard mode timings. Modes that are out of monitor
spec
# are automatically deleted by the server (provided the HorizSync and
# VertRefresh lines are correct), so there's no immediate need to
# delete mode timings (unless particular mode timings don't work on your
# monitor). With these modes, the best standard mode that your monitor
# and video card can support for a given resolution is automatically
# used.

# 640x400 @ 70 Hz, 31.5 kHz hsync
Modeline "640x400"     25.175 640  664  760  800   400  409  411  450
# 640x480 @ 60 Hz, 31.5 kHz hsync
Modeline "640x480"     25.175 640  664  760  800   480  491  493  525
# 800x600 @ 56 Hz, 35.15 kHz hsync
ModeLine "800x600"     36     800  824  896 1024   600  601  603  625
# 1024x768 @ 87 Hz interlaced, 35.5 kHz hsync
Modeline "1024x768"    44.9  1024 1048 1208 1264   768  776  784  817
Interlace

# 640x480 @ 72 Hz, 36.5 kHz hsync
Modeline "640x480"     31.5   640  680  720  864   480  488  491  521
# 800x600 @ 60 Hz, 37.8 kHz hsync
Modeline "800x600"     40     800  840  968 1056   600  601  605  628
+hsync +vsync

# 800x600 @ 72 Hz, 48.0 kHz hsync
Modeline "800x600"     50     800  856  976 1040   600  637  643  666
+hsync +vsync
# 1024x768 @ 60 Hz, 48.4 kHz hsync
Modeline "1024x768"    65    1024 1032 1176 1344   768  771  777  806
-hsync -vsync

# 1024x768 @ 70 Hz, 56.5 kHz hsync
Modeline "1024x768"    75    1024 1048 1184 1328   768  771  777  806
-hsync -vsync
# 1280x1024 @ 87 Hz interlaced, 51 kHz hsync
Modeline "1280x1024"   80    1280 1296 1512 1568  1024 1025 1037 1165
Interlace

# 1024x768 @ 76 Hz, 62.5 kHz hsync
Modeline "1024x768"    85    1024 1032 1152 1360   768  784  787  823
# 1280x1024 @ 61 Hz, 64.2 kHz hsync
Modeline "1280x1024"  110    1280 1328 1512 1712  1024 1025 1028 1054

# 1280x1024 @ 74 Hz, 78.85 kHz hsync
Modeline "1280x1024"  135    1280 1312 1456 1712  1024 1027 1030 1064

# 1280x1024 @ 76 Hz, 81.13 kHz hsync
Modeline "1280x1024"  135    1280 1312 1416 1664  1024 1027 1030 1064

# Low-res Doublescan modes
# If your chipset does not support doublescan, you get a 'squashed'
# resolution like 320x400.

# 320x200 @ 70 Hz, 31.5 kHz hsync, 8:5 aspect ratio
Modeline "320x200"     12.588 320  336  384  400   200  204  205  225
Doublescan
# 320x240 @ 60 Hz, 31.5 kHz hsync, 4:3 aspect ratio
Modeline "320x240"     12.588 320  336  384  400   240  245  246  262
Doublescan
# 320x240 @ 72 Hz, 36.5 kHz hsync
Modeline "320x240"     15.750 320  336  384  400   240  244  246  262
Doublescan
# 400x300 @ 56 Hz, 35.2 kHz hsync, 4:3 aspect ratio
ModeLine "400x300"     18     400  416  448  512   300  301  602  312
Doublescan
# 400x300 @ 60 Hz, 37.8 kHz hsync
Modeline "400x300"     20     400  416  480  528   300  301  303  314
Doublescan
# 400x300 @ 72 Hz, 48.0 kHz hsync
Modeline "400x300"     25     400  424  488  520   300  319  322  333
Doublescan
# 480x300 @ 56 Hz, 35.2 kHz hsync, 8:5 aspect ratio
ModeLine "480x300"     21.656 480  496  536  616   300  301  302  312
Doublescan
# 480x300 @ 60 Hz, 37.8 kHz hsync
Modeline "480x300"     23.890 480  496  576  632   300  301  303  314
Doublescan
# 480x300 @ 63 Hz, 39.6 kHz hsync
Modeline "480x300"     25     480  496  576  632   300  301  303  314
Doublescan
# 480x300 @ 72 Hz, 48.0 kHz hsync
Modeline "480x300"     29.952 480  504  584  624   300  319  322  333
Doublescan

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier	"Generic VGA"
    VendorName	"Unknown"
    BoardName	"Unknown"
    Chipset	"generic"

#    VideoRam	256

#    Clocks	25.2 28.3

EndSection

# Sample Device for accelerated server:

# Section "Device"
#    Identifier	"Actix GE32+ 2MB"
#    VendorName	"Actix"
#    BoardName	"GE32+"
#    Ramdac	"ATT20C490"
#    Dacspeed	110
#    Option	"dac_8_bit"
#    Clocks	 25.0  28.0  40.0   0.0  50.0  77.0  36.0  45.0
#    Clocks	130.0 120.0  80.0  31.0 110.0  65.0  75.0  94.0
# EndSection

# Device configured by xf86config:

Section "Device"
    Identifier  "S3-ViRge"
    VendorName  "S3"
    BoardName   "PCI"
    #VideoRam    2048
# Use Option "nolinear" if the server doesn't start up correctly
# (this avoids the linear framebuffer probe). If that fails try
# option "nomemaccess".
#
# Refer to /usr/X11R6/lib/doc/README.S3, and the XF86_S3 man page.
    Ramdac      "s3gendac"
    Clockchip   "s3gendac"
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# The Colour SVGA server

Section "Screen"
    Driver      "svga"
    Device      "Generic VGA"
    #Device      "S3-ViRge"
    Monitor     "SC-528MXLJ"
    Subsection "Display"
        Depth       8
        #Modes       "640x480" "800x600" "1024x768" "1280x1024"
        ViewPort    0 0
        Virtual     320 200
        #Virtual     1280 1024
    EndSubsection
EndSection

# The 16-color VGA server

Section "Screen"
    Driver      "vga16"
    Device      "Generic VGA"
    Monitor     "SC-528MXLJ"
    Subsection "Display"
        Modes       "640x480" "800x600"
        ViewPort    0 0
        Virtual     800 600
    EndSubsection
EndSection

# The Mono server

Section "Screen"
    Driver      "vga2"
    Device      "Generic VGA"
    Monitor     "SC-528MXLJ"
    Subsection "Display"
        Modes       "640x480" "800x600"
        ViewPort    0 0
        Virtual     800 600
    EndSubsection
EndSection

# The accelerated servers (S3, Mach32, Mach8, 8514, P9000, AGX, W32,
Mach64)

Section "Screen"
    Driver      "accel"
    Device      "S3-ViRge"
    Monitor     "SC-528MXLJ"
    Subsection "Display"
        Depth       8
        Modes       "640x480" "800x600" "1024x768" "1280x1024"
        ViewPort    0 0
        Virtual     1280 1024
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "640x480" "800x600" "1024x768"
        ViewPort    0 0
        Virtual     1024 768
    EndSubsection
    Subsection "Display"
        Depth       32
        Modes       "640x480" "800x600"
        ViewPort    0 0
        Virtual     800 600
    EndSubsection
EndSection

----------------------- cut XF86Config end ----------------------
・今までにやったことは、Kernelのバージョンアップ 1.3.80 -> 2.0.28
・XF86_S3Vの追加。
・xf86config
・FAQ等の閲覧
・XF86_SVGAでは、Xは立ち上がります。（これでは、画面が大きすぎてOperation
できない。）

PC/AT互換機の構成
  cpu:Pentium 133Mhz ,Memory:48Mb ,HDD:800Mb + 2Gb ,Video chip:S3 ViRge
  VRAM:2Mb ,Monitor:15inch hsync->24-66KHz vsync->50-120KHz 

長文になり、ご迷惑おかけしますが、御教授の程宜しくお願いします。
/*********************************************************/
/*             新垣 ： arakaki _at_ po.jah.or.jp              */
/*********************************************************/
この情報があなたの探していたものかどうか選択してください。
yes/まさにこれだ！   no/違うなぁ   part/一部見つかった   try/これで試してみる
あなたが探していた情報はどのようなことか、ご自由に記入下さい。特に「まさにこれだ！」と言う場合は記入をお願いします。
例:「複数のマシンからCATV経由でipmasqueradeを利用してWebを参照したい場合の設定について」
Follow-Ups: